logoooo image
queen appointment warrent raster

By Appointment to Her Majesty The Queen Manufacturers of Wood Finishes Morrells Wood Finishes Ltd Stockport

induro® XLA ANTI-SLIP Floor Lacquer

XLA ANTI-SLIP is a two pack waterborne polyurethane lacquer that is highly resistant to scuffs, spills and marks. Suitable for domestic and commercial high traffic areas with wooden floors. induro® XLA ANTI-SLIP meets wet slip accreditation BS 7976-2. This varnish is designed to reduce slip potential in bars, clubs, hospitals, schools, shopping centres and all other high-traffic public areas. 

Use after induro® GP Seal / ISO Seal and 2 - 3 coats of induro® XL2 for a strong yet flexible varnish. Maintain SPORT with induro ®Maintenance products.

Preparation

Prior to starting the sanding process the floor should be checked for any protruding nail or screw heads and these should either be removed or countersunk. All wooden floors requiring varnish will have to be sanded. Newly laid floors are sanded to achieve a nice level floor and old floors are sanded to remove existing finishes and to level out worn and heavily used areas.

Sanding will have to be carried out in several grit stages and this will be dependent on the unevenness and general condition of the floor.

Staining

Morrells standard Light Fast range of stains give excellent grain definition and overall colour. Due to this range being spirit based (fast drying), care should be taken on application not to stain too large an area at once as this could lead to a patchy appearance once the stain is dry.

  1. Stain should be applied by brush/rag or mohair pad
  2. Remove excesses with a clean rag

It is important to remove as much of excess stain as possible so as not to create a film as this could result in poor adhesion of subsequent coats of lacquer.

Stains intended for other uses i.e. decking, fencing, garden furniture etc should not be considered for floors as these will contain water-repelling properties, and therefore water based floor lacquers would not adhere to these stains.

Application Guidelines

  1. Do not denib the sealer
  2. Denib between coats of induro® XL2 and XLA
  3. mix 9 parts lacquer to 1 part catalyst by volume
  4. add catalyst into the can of lacquer, replace top, turn upside down and shake vigorously for 1 minute
  5. allow lacquer to stand for 5 minutes before use (use within 5 hours of mixing)
  6. apply using a short mohair roller or similar, or mohair flooring pad or t-bar applicator
  7. apply lacquer evenly making smooth passes, predominantly along the grain
  8. avoid pooling of lacquer

induro® Application Tips

  1. avoid equipment containing copper, iron, zinc, aluminium and platinum
  2. carry out an adhesion test on a small test area when overcoating non-induro® flooring products
  3. use equipment solely nominated for waterborne products only
  4. not suitable for pulling over
  5. optimum application between 18°C and 22°C with good air movement and ventilation
  6. for professional use only

Application

  1. After 80-100 grit sanding stage, mix induro® Mix'n'Fill with sanding dust and fill gaps smaller than 6mm
  2. Fill gaps larger than 6mm with Hot-Melt Filler or Morrells® One-Part or Two-Part Filler
  3. Complete the sanding regime

Domestic

  1. 1 coat of induro® GP Floor Sealer and Primer at 130-150ml per m2 (Dry Film Thickness ~ 42μm)
  2. Do not sand or denib the sealer coat
  3. 1 coat of induro® XL2 Floor Lacquer at 100-120ml/m2 (Dry Film Thickness ~ 30-35μm)
  4. Lightly sand the coat with rotary sander 150-180 grit mesh
  5. Sweep and vacuum the floor
  6. 1 coat of induro® XLA Floor Lacquer at 100-120ml/m2 (Dry Film Thickness ~ 30-35μm)

Commercial

  1. 1 coat of induro® GP Floor Sealer and Primer at 130-150ml per m2 (Dry Film Thickness ~ 42μm)
  2. Do not sand or denib the sealer coat
  3. 2-3 coats of induro® XL2 Floor Lacquer at 100-120ml/m2 (Dry Film Thickness ~ 30-35μm)
  4. Between each coat of XL2, lightly sand with rotary sander 150-180 grit mesh, and sweep and vacuum the floor
  5. 1 coat of induro® XLA at 100-120ml/m2 (Dry Film Thickness ~ 30-35μm)

  • Pack size: 5L
  • Catalysis: 9 parts lacquer : 1 part catalyst by volume
  • Pot life: 5 hours
  • Touch dry: 20 - 30 minutes @ 18°C
  • Recoatable: 2 - 3 hours minimum @ 18°C
  • Coats: 1 (after 1 coat of GP and 2 - 3 coats XL2)
  • Light use: 24 hours @ 18°C
  • Fully hard: 5 - 7 days @ 18°C
  • Traffic: medium - high traffic once fully hard
  • Coverage: 60m² per 5 litres dependent upon the size, orientation and surface quality of the item being coated

Product Codes

8GL/314B induro® XLA 90% gloss
8SA/314B induro® XLA 50% satin
8SM/314B induro® XLA 30% semi-matt
8MA/314B induro® XLA 10% matt
8CAT/INDURO Catalyst for induro® XLA ANTI-SLIP

MSDS

Visit our Data Sheet page for access to all available data sheets.

Input your information below to begin download.